How to Bind Your Quilt

posted in: Quilting | 0

In my previous post/video, I talked about how to make your binding. Now it’s time to put it on your quilt.

I only use my machine when binding, so this is how I’m going to teach in this tutorial.

Tools Needed

  • Sewing Machine
  • Matching Thread
  • Binding

Sew On Back of Quilt

I want the pretty part of my binding on the front, so I’m going to by attaching the binding to the back of the quilt.

Start in the middle of the side of your quilt, and leave a 10 in tail before starting your stitch line.

You will line up the raw edge of your binding, to the raw edge of your quilt. Sew 1/4″ from the side of the quilt. I use 1/4″ foot to help me line it up properly. Sew it all the way down to almost the corner.

When you are 1/4″ away from the corner or edge of your quilt, with the needle down, pivot your foot 45 degrees so it’s face right into the corner.

Sew into the corner and cut threads.

**This is next part might be easier to see in the video, but I will try really hard to explain it properly.**

Before you start sewing it down toward the next side, fold the binding back at a 45 degree angle so the long end is off your quilt.

Then fold it back on itself, so the fold lines up with that first edge of your quilt.

It should now be laying flat along the second edge of your quilt, with raw edges of binding lining up with the edge of the quilt.

Starting off the edge of the quilt, sew 1/4″ all the way down that second edge of the quilt, lining up the binding and attaching it as you go.

Repeat the above directions for all 4 corners.

Once you get back to the first side, stop attaching the binding so you have roughly 10-12 in. from where you started the binding.

Take your quilt to the table and lay it flat, back side up. Lay the tail from the beginning and lay it along the edge of the quilt, as if you want to sew it down.

Trim a small piece of binding, we will use it as a guide.

Open up the binding piece, so it’s laying flat, and put it at the end of this tail.

Coming from the opposite direction, lay that binding along the edge of the quilt so it over laps the binding, as well as your guide.

Cut off that second piece where the end of the guide is. The idea is the bindings will overlap for the length of how long that guide is.

Now open up the two ends of the binding and lay them right sides together on a 45 degree angle.

Draw a line at the diagonal so the edges are on one side of the line and the strips attached to the quilt are on the other.

Pin your pieces together.

Sew along the drawn line. Before trimming, pull them straight so that you know you sowed them right. (I have been know to twist one side, so make sure you check before trimming.)

Trim off the salvedge side 1/4″ from the seam line.

Fold the pieces back down so they lay right along the edge of the quilt, the raw edges of the binding lining up with the edge of the quilt.

Make sure your seam is laying flat and then sew it 1/4″ from the side of the quilt, attaching the binding to the quilt.

Finish Binding On Front of Quilt

We are now going to fold the binding towards over toward the edge of the quilt, and around to the front.

I like to use binding clips to keep the binding in place. I put them every 6-8 in.

Make sure your thread matches your binding or it will look funny. But it’s now time to attach it to the front of your quilt. You want to sew just inside the edge of your binding. Once again I start in the middle of a side and slowly go down the first side of my quilt removing the binding clips as I go.

Stop about 3 in from the corner, with your needle and foot still down.

make sure the first side of binding is laying flat on your quilt. At the corner it will look like it’s at a 45 degree angle. Run your finger time along the edge so it creates a crisper edge.

Then fold the second side down over the top, taking care the corner doesn’t fold all wonky. If done correctly, it should look like a mitered corner.

Sew to the corner of your quilt, just until your needle hits the mitered corner. Make sure you caught that second side of the quilt’s binding.

Keep your needle down and pivot your quilt 90 degrees and then sew down the next side.

Complete all 4 sides and all 4 corners, overlapping about an inch when you get back to your starting point.

Questions

If you have any questions, please go watch the YouTube video (above). I go into much more detail in the video, and you can watch it and follow along.

If you have questions after that, drop them in my comment section below, or on the comment section of the video and I will come and answer them.

Tag me!

I would love to see your progress. Just tag me at #theashleytomlinson or #ashley_sunnymade and I’ll be able to see you on social media. 

I want to see how they turn out!

Happy sewing!